How to make a homemade pipe out of a water bottle

How to make a homemade pipe out of a water bottle how to#
How to make a homemade pipe out of a water bottle install#
How to make a homemade pipe out of a water bottle manual#
How to make a homemade pipe out of a water bottle professional#

Reinsert the original plumbing and tighten the cap.Д¦) Assemble the spout section in place. Poke the metal pipe section up through the well cap and thread the steel coupler (Item 8) on tight. Be gentle, too, with the existing wiring and pipes. Working together to create an arc with the pipe, allow the foot valve end to snake itself down the well casing, being careful not to bend it too sharply. Two strong people can do this by having one person at the foot valve end and the other about 30 feet up on the pipe. (You may want to hire a well technician, if only to use his hoisting equipment!)ДҐ) Feed the main pipe section into the well. You definitely don't want to lose anything down your well. Get a safety rope on any equipment below the old cap before freeing the cap completely. If you're familiar with your existing well plumbing, you can gauge how much weight you will be dealing with. Allow ample cure time for all glued PVC joints.Д¤) Before installing the pump and new well cap, you'll need to remove the old cap. Bevel inside edges to allow easy insertion of the rod section later. This includes items passing through the well cap (Item 9) and below. If your existing electric submersible pump uses torque arresters, they may need to be modified or removed, depending on design, at your discretion.Дў) Glue the rod section together, as shown here, following the instructions on the primer and cement product cans (see the Materials Chart in the image gallery, Items 15 and 16).ДЈ) Glue and screw the lower main pipe section together, as shown on the first illustration. You may have to drill a hole in the new cap for either the air vent or wiring access hole.

How to make a homemade pipe out of a water bottle install#

You'll also want to make sure that the pump you install complies with any pertinent codes or laws in your area.Д«efore you begin, read through the instructions, gather tools and materials, then proceed as follows:ДЎ) Examine your existing well cap configuration, then purchase a new one with an additional port for a 1 1/4 inch pipe. Diluted chlorine should be used to wash all pipes as they are installed. Should you opt to go the do-it-yourself route, a word of caution: Before beginning any work that involves altering existing plumbing or wiring, the electric power supply must be shut off and there can be no pressure in the water lines (open the faucet nearest the well and wait for the water flow to stop).

How to make a homemade pipe out of a water bottle professional#

If you have never worked on or are unfamiliar with the existing components of your well, it may be worth it to hire a professional to handle the installation. While the Holopump is fairly easily assembled, getting it down your well properly is a bit more complicated.

How to make a homemade pipe out of a water bottle manual#

(To build an 80-foot-long pump, simply replace the last segment of both the rod and water pipe with 20-foot lengths of PVC, rather than the 10-foot lengths shown in the plans.) Assembly and Installation of the PVC Manual Well Pump Although I know that some people have successfully gone a little deeper with my design, I still say the 60-foot model (using 70 or 80 feet of pipe) is the practical depth limit for this pump, and so that's the maximum length I am willing to recommend. The plans on these pages are for a 70-foot-long Holopump, which is perfect for a well with a 60-foot static water level. In such a case, a 40-foot Holopump (made with two 20-foot lengths of pipe) would work just fine. A person may have a 175-foot well, but a static water level of 30 feet. Water level is the distance from mound level to the surface of your well water. It's important to distinguish between these two concepts: Well depth is the distance from ground level to the bottom of your well. at a cost of only about $120 for the whole shebang. All of the parts are available from, or can be ordered through, most any hardware store. The result is an invention I've dubbed the 'Holopump,' a PVC manual well pump capable of efficiently drawing water from as deep as 60 feet. Out of frustration, I hit the drawing board, determined to devise a solution. Mid- to deep-well jack pumps will draw water from depths as low as 300 feet, but they'll also leave an $800-plus hole in your wallet.

Lightweight manual pitcher pumps sell for around $50, but unfortunately these only work to a depth of about 25 feetВ - some 20 feet short of what we needed. I wanted something I could install alongside our submersible electric pump, but I didn't want to spend a fortune. Turns out that was easier said than done.

How to make a homemade pipe out of a water bottle how to#

Learn how to build a homemade PVC manual well pump.ДЄfter several power outages left us wanting for water, I decided it was time to install a hand pump on our 45-foot-deep well.